Grizzly 700 Diagnostic Codes - Grizzly Riders - Yamaha Grizzly ATV Forum
 
 
Grizzly Riders Homepage Yamaha Grizzly Forums The Grizzly Garage User Control Panel Register Today It's Free Store  

Go Back   Grizzly Riders - Yamaha Grizzly ATV Forum > Grizzly Forums > Grizzly Tech Tips

Notices

Grizzly Tech Tips Share tips on services, repairs, etc here


» Site Navigation
 > FAQ
 > Garage
» ----------------------
» Other Sites
» ----------------------
» View us On
» Grizzly Riders Swag

» We Support our Troops

» Donate to Grizzly Riders.
If you like this website and would like to give something back in return, you can make a donation. Your donation will be used to pay for site hosting service, software, domains and maintenance costs.


Reply
 
LinkBack (1) Thread Tools Display Modes
  1 links from elsewhere to this Post. Click to view. #1 (permalink)  
Old 08-07-2009, 09:58 PM
TheGrizz's Avatar
Welcome to Grizzly Riders! How May I Help You?
We see everything!
 
Join Date: May 2009
Location: West Virginia
Posts: 7,925

Thanks: 643
Thanked 1,484 Times in 650 Posts
Send a message via Yahoo to TheGrizz
Visit TheGrizz's Facebook Visit TheGrizz's Twitter Visit TheGrizz's YouTube
Default Grizzly 700 Diagnostic Codes

Grizzly 700 Diagnostic Codes


Diagnostic code number on display followed by checking method.

D01
Throttle angle
• Fully closed position 15 ~ 20 Check with throttle fully closed.
• Fully opened position 95 ~ 100 Check with throttle fully open.

D03
Pressure difference (atmospheric pressure and intake air pressure).
Displays the intake air pressure. Set the engine stop switch to "RUN", then operate the throttle while pushing the start switch. (If the display value changes, the performance is OK.)

D05
Intake air temperature.
Displays the intake air temperature. Compare the actually measured intake air temperature with the meter.

D06
Coolant temperature.
Displays the coolant temperature. Compare the actually measured coolant temperature with the meter.

D07
Vehicle speed pulse 0 ~ 999
Check that the number increases when the rear wheel is rotated. The number is cumulative and does not reset each time the wheel is stopped.

D08
Lean angle sensor Remove the lean angle sensor and...
• Upright 0.4 ~ 1.4 incline it more than 65 degrees.
• Overturned 3.7 ~ 4.4

D09
Fuel system voltage (battery voltage): Approximately 12.0
Set the engine stop switch to "RUN", and then compare with the actually measured battery voltage. (If the battery voltage is lower, perform recharging).

D21
Neutral switch Shift the transmission.
• Neutral ON
• In gear OFF

D60
EEPROM fault code display.
• No history 00
• History exists 01

D61
Malfunction history code display.
• No history 00
• History exists Fault codes 12-50
• (If more than one code number is detected, the display alternates every two seconds to show all the detected code numbers. When all code numbers are shown, the display repeats the same process.)

D62
Malfunction history code erasure.
• No history 0 —
• History exists Up to 16 fault codes To erase the history, set the engine stop switch to "OFF" and then to
"RUN".

D70 Control number 00 ~ 255

Setting the diagnostic mode
1. Turn the main switch to “OFF” and set the
engine stop switch to “OFF”.
2. Disconnect the wire harness coupler from
the fuel pump.
3. Simultaneously press and hold the
“SELECT” and “RESET” buttons, turn the
main switch to “ON”, and continue to press
the buttons for 8 seconds or more.

NOTE:
• All displays on the meter disappear.
• “dIAG” appears on the LCD meter.
4. Simultaneously press the “SELECT” and
“RESET” buttons for 2 seconds or more to
execute the selection.
5. Select the diagnostic code number that
applies to the item that was verified with the
fault code number by pressing the
“SELECT” and “RESET” buttons.

NOTE:
• The diagnostic code number appears on the
LCD meter (01-70).
• To decrease the selected diagnostic code
number, press the “RESET” button. Press
the “RESET” button for 1 second or longer to
automatically decrease the diagnostic code
numbers.
• To increase the selected diagnostic code
number, press the “SELECT” button. Press
the “SELECT” button for 1 second or longer
to automatically


According to the manual, many of the errors that get thrown are posted on the LCD and you don't need to go into diagnostic mode.

You can erase the error history by setting the engine run switch off and back on when it is in diagnostic mode on D62.

Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote

  #ADS  
Advertiser Advertiser is online
Circuit advertisement
 
Join Date: Always
Location: Advertising world
Age: 2010
Posts: Many

Thanks: 643
Thanked 1,484 Times in 650 Posts

Reply

Bookmarks

Tags
700, codes, diagnostic, grizzly

LinkBacks (?)
LinkBack to this Thread: http://grizzlyriders.com/forums/grizzly-tech-tips/145-grizzly-700-diagnostic-codes.html
Posted By For Type Date
Grizzly 700 Diagnostic Codes - Grizzly Riders - Yamaha Grizzly ATV Forum This thread Refback 09-10-2013 08:14 PM


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -4. The time now is 02:29 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 2011 Grizzly Riders
 
GrizzlyRiders.com is an independent Yamaha enthusiast website. Content on GrizzlyRiders.com is generated by its users and GrizzlyRiders.com is not in any way affiliated with Yamaha Motor Corporation, U.S.A.